Anti-Static Bag triggers Touch Points on #PineDio Stack #BL604 ... This could be our "Robot Finger" for Auto-Testing the Touch Panel 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Motor with Anti-Static Bag ... Might work for Auto-Testing the #PineDio Stack Touch Screen 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Wiring up #PineDio Stack #BL604 @PINE64 and PineCone BL602 ... To SBC for Auto Flash & Test 🤔

https://lupyuen.github.io/articles/auto

Connect these pins on #PineDio Stack #BL604 to our SBC for Auto Flash & Test: 1️⃣ GPIO 8 2️⃣ Reset 3️⃣ Ground

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604: GPIO 8 is already connected to SBC ... But GPIO 8 Jumper MUST be set to Low ... Otherwise the LoRaWAN Auto-Test goes wonky and fails 🤔

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

#PineDio Stack #BL604 and PineCone BL602 ... All boxed up with SBC for Auto Flash & Test 🙏

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604 @PINE64 ... Yep it works! 🎉 ... Up Next: Robot Finger 🤖 👉

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Here's how we Auto Upload the Test Log to GitHub Releases ... Thanks to GitHub CLI 👍

https://github.com/lupyuen/remote-bl602#upload-test-log

Automated Testing of Apache #NuttX RTOS on #PineDio Stack #BL604 @PINE64 ... All shall be explained in this article

https://lupyuen.github.io/articles/auto2?1

Apache #NuttX Testing on #PineDio Stack #BL604 is now Fully Automated ... Except for the Touch Panel which needs a Human Touch 👉

https://lupyuen.github.io/articles/auto2?2

Automated Testing on #PineDio Stack #BL604 covers GPIO, SPI, I2C, LoRaWAN and Touch Panel

https://lupyuen.github.io/articles/auto2?3#testing-checkpoints

Here's how we connect #PineDio Stack #BL604 to an SBC for Automated Testing

https://lupyuen.github.io/articles/auto2?4#connect-pinedio-stack-to-sbc

How we run the Automated Test for Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?5#run-automated-test

Our Automated Test Script flashes and boots Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?6#nuttx-must-boot

Here's how we automagically flash and boot #PineDio Stack #BL604 with an SBC

https://lupyuen.github.io/articles/auto2?7#checkpoint-alpha

Our Automated Test for #PineDio Stack #BL604 detects whether Apache #NuttX RTOS has crashed ... And runs a Crash Analysis

https://lupyuen.github.io/articles/auto2?8#nuttx-must-not-crash

Our Automated Test for #PineDio Stack #BL604 decodes the addresses in the Crash Dump ... By looking up the #RISCV Disassembly

https://lupyuen.github.io/articles/auto2?9#checkpoint-bravo

SPI Bus on #PineDio Stack #BL604 is shared by 3 SPI Devices ... Here's how we do the Automated SPI Test

https://lupyuen.github.io/articles/auto2?10#spi-test

@sad_electronics @lupyuen @PINE64 afaik CIA has tools to reconstruct the missing geometry, but i am not sure how usable it is.

@sad_electronics @PINE64 Me too! 🙂

@lupyuen I'm excited about the future of the little LoRa devices

@minnix Plenty more LoRa Devices on Tindie 🙂

https://www.tindie.com/search/?q=Lora

@sad_electronics Cool thanks! Lemme put a motor inside the ESD Bag ... See whether it can trigger touch points when needed