Weird Antenna ... But works great with #LoRa on #PineDio Stack #BL604 @PINE64 ! 👍

https://lupyuen.github.io/articles/pinedio2

#PineDio Stack #BL604 exposes GPIO 8 (on GPIO Port) and Reset Pin (on JTAG Port) ... We could connect them to an SBC for Auto Flash & Test 🤔

https://lupyuen.github.io/articles/auto

Anti-Static Bag triggers Touch Points on #PineDio Stack #BL604 ... This could be our "Robot Finger" for Auto-Testing the Touch Panel 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Motor with Anti-Static Bag ... Might work for Auto-Testing the #PineDio Stack Touch Screen 🤔

https://lupyuen.github.io/articles/pinedio2#automated-testing

Wiring up #PineDio Stack #BL604 @PINE64 and PineCone BL602 ... To SBC for Auto Flash & Test 🤔

https://lupyuen.github.io/articles/auto

Connect these pins on #PineDio Stack #BL604 to our SBC for Auto Flash & Test: 1️⃣ GPIO 8 2️⃣ Reset 3️⃣ Ground

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604: GPIO 8 is already connected to SBC ... But GPIO 8 Jumper MUST be set to Low ... Otherwise the LoRaWAN Auto-Test goes wonky and fails 🤔

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

#PineDio Stack #BL604 and PineCone BL602 ... All boxed up with SBC for Auto Flash & Test 🙏

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Auto Flash & Test on #PineDio Stack #BL604 @PINE64 ... Yep it works! 🎉 ... Up Next: Robot Finger 🤖 👉

https://github.com/lupyuen/remote-bl602#pinedio-stack-bl604

Here's how we Auto Upload the Test Log to GitHub Releases ... Thanks to GitHub CLI 👍

https://github.com/lupyuen/remote-bl602#upload-test-log

Automated Testing of Apache #NuttX RTOS on #PineDio Stack #BL604 @PINE64 ... All shall be explained in this article

https://lupyuen.github.io/articles/auto2?1

Apache #NuttX Testing on #PineDio Stack #BL604 is now Fully Automated ... Except for the Touch Panel which needs a Human Touch 👉

https://lupyuen.github.io/articles/auto2?2

Automated Testing on #PineDio Stack #BL604 covers GPIO, SPI, I2C, LoRaWAN and Touch Panel

https://lupyuen.github.io/articles/auto2?3#testing-checkpoints

Here's how we connect #PineDio Stack #BL604 to an SBC for Automated Testing

https://lupyuen.github.io/articles/auto2?4#connect-pinedio-stack-to-sbc

How we run the Automated Test for Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?5#run-automated-test

Our Automated Test Script flashes and boots Apache #NuttX RTOS on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?6#nuttx-must-boot

Here's how we automagically flash and boot #PineDio Stack #BL604 with an SBC

https://lupyuen.github.io/articles/auto2?7#checkpoint-alpha

Our Automated Test for #PineDio Stack #BL604 detects whether Apache #NuttX RTOS has crashed ... And runs a Crash Analysis

https://lupyuen.github.io/articles/auto2?8#nuttx-must-not-crash

Our Automated Test for #PineDio Stack #BL604 decodes the addresses in the Crash Dump ... By looking up the #RISCV Disassembly

https://lupyuen.github.io/articles/auto2?9#checkpoint-bravo

SPI Bus on #PineDio Stack #BL604 is shared by 3 SPI Devices ... Here's how we do the Automated SPI Test

https://lupyuen.github.io/articles/auto2?10#spi-test

Automated Test for #LoRaWAN on #PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?11#lorawan-test

#PineDio Stack #BL604 connects to ChirpStack #LoRaWAN Gateway ... And sends a Data Packet from Apache #NuttX RTOS

https://lupyuen.github.io/articles/auto2?12#lorawan-test

Our Automated #LoRaWAN Test on #PineDio Stack #BL604 ... Calls a bunch of #NuttX Libraries and Drivers

https://lupyuen.github.io/articles/auto2?15#checkpoint-delta

(Mostly) Automated Testing of I2C Touch Panel on #PineDio Stack #BL604 with Apache #NuttX RTOS

https://lupyuen.github.io/articles/auto2?16#touch-panel-test

Inside our Touch Panel Test for #PineDio Stack #BL604 on Apache #NuttX RTOS ... And how we might automate the test

https://lupyuen.github.io/articles/auto2?17#checkpoint-echo

#PineDio Stack Automated Test Log gets uploaded to GitHub Release Notes ... By calling the #GitHub CLI

https://lupyuen.github.io/articles/auto2?18#upload-test-log

We pull updates from #NuttX Mainline and test them on #PineDio Stack #BL604 every 2 weeks

https://lupyuen.github.io/articles/auto2?19#merge-updates-from-nuttx

Syncing Apache #NuttX RTOS with #PineDio Stack #BL604 and PineCone BL602 ... Looks complicated but I'll explain everything

https://lupyuen.github.io/articles/auto2?20#merge-updates-from-nuttx

Here's how we merge updates from #NuttX Mainline into PineCone #BL602 and PineDio Stack #BL604

https://lupyuen.github.io/articles/auto2?21#pinecone-to-pinedio-stack