Show newer

@niconiconi was it you who described how high ESR of large electrolytic caps after something like a buck converter helps prevent voltage oscillations?

@_thegeoff

I'd not be surprised if there were various hydrates there, but I don't think that alone would explain how the crystal grows on the end that's far away from the liquid, or would it?

@m0bi @rower

O, trójkołowiec z dwoma kołami z przodu, które są skrętne. Z tego co pamiętam (z bloga kogoś, kto taki konstruował iirc) jest coś nieoczywistego w konstrukcji mechanizmu kierującego takimi kołami, co trzeba wziąć pod uwagę, żeby uzyskać rozsądną stabilność w skrętach.

@_thegeoff

I would be extremely surprised if I could get mass transport through a crystal where all the liquid was bound into hydrates. After all, I can't see how I can get mass transfer without having ions dissolved in the liquid, which can't work then (right?).

@lauren

Do you mean left as in more redistribution towards a wide group of people, or that and also more freedom from traditional social structures?

@_thegeoff

I put a safety pin (which I falsely thought wasn't stainless, apparently) in a bit of brine in a mug and left it for 2 weeks on my desk. The mug ended up covered in salt crystals from the level of brine up to the edge, and even a bit beyond the edge. My only hypothesis how the salt gets transported to grow this crystal layer is as brine, through the crystal (which must be wet via capillary action). The surprising thing is that I can barely notice the crystals on walls are conductive (which a colleague suggested to me as a test for whether the crystals are moist) -- if I use my multimeter probes stuck <5mm apart, I sometimes get ~15MOhms. I haven't gotten around to measuring conductivity more properly (using contacts of larger surface area, looking at more of the V/I curve, etc.).

Another interesting thing is that the crystallized thing on the walls seems to have at least two layers of different structure. I haven't tried to figure out why yet (one hypothesis that I have is that it's related to the brine being made from iodized salt).

@wolf480pl I used a shortlived system that for some reason had an equivalent of vimpager set as the pager for manpages.

@delroth I'm curious how soon they will send an abuse complaint to themselves or their provider (assuming they have more than one).

@deep Poza tym nie wygląda na to, że podgrupy do badania były wybrane zawczasu (na szybko nie znalazłem stwierdzenia, żeby tak było, a narracja trochę sugeruje przeciwnie, przeplatając opis wyników z opisem tego jakie jeszcze rzeczy wyciągali z tych danych), więc to może być przykład na xkcd.com/882/

@x43r0 @sophieschmieg

I'm not OP but I'd rate Orbiter and Children of Dead Earth highest.

@freemo @rchusid

The text of SESTA I could find (congress.gov/bill/115th-congre) doesn't seem to have any such effects. Do you have a reference that mentions that effect?

@ruuda Maybe some zeroes get interspersed inbetween actual samples?

@aredridel

Do you think that the phone network shares these problems, or maybe they're ameliorated somehow there?

@gvs @neatchee

This might not be as obvious in some places. For example, in some places the company cannot lower the salary, even to a value that's higher than the original salary in the employment contract (not taking into account any subsequent raises). If they want to do that, they need to satisfy the requirements for firing the employee (and, if the employee demurs, they need to actually fire him). I wouldn't be surprised if, at least in some places, same applied to working conditions.

@bagder

It might be interesting to see this with log scale on y axis and, if those lines seem to decrease roughly linearly, to compare how halflifes change over time.

@_thegeoff @simon_brooke @raspberry_pi

An idea (I'm not entirely sure if that's what Simon meant) is not to run blender and slicer there, but to slice it on your desktop, and cause the raspi to feed the sliced file to the printer.

octoprint is a tool that does that (imo well), and at least PrusaSlicer has integration with it, insofar you can tell it "send the sliced gcode to the remote octoprint and command it to start printing it".

@literalgrill

What's the consequence of declaring a stream to contain "politics and sensitive social issues"? Does it prevent monetization?

I wonder if some streamers will decide to just declare all their streams to be like that in a form of protest, because after all this is such a broad category that something from it always can come up.

@aredridel @brainwane

Are you saying that it's as ill-defined as "average person"?

TIL that there's a detective Monk movie released last year.

Show older
Qoto Mastodon

QOTO: Question Others to Teach Ourselves
An inclusive, Academic Freedom, instance
All cultures welcome.
Hate speech and harassment strictly forbidden.